Widescreen signaling

In television technology, Wide Screen Signaling (WSS) is digital metadata embedded in invisible part of the analog TV signal describing qualities of the broadcast, in particular the intended aspect ratio of the image. This allows television broadcasters to enable both 4:3 and 16:9 television sets to optimally present pictures transmitted in either format, by displaying them in full screen, letterbox, widescreen, pillar-box, zoomed letterbox, etc.

This development is related to introduction of widescreen TVs and broadcasts, with the PALplus system in the European Union (mid 1990s), the Clear-Vision system in Japan (early 1990s), and the need to downscale HD broadcasts to SD in the US. The bandwidth of the WSS signal is low enough to be recorded on VHS (at the time a popular home video recording technology). It is standardized on Rec. ITU-R BT.1119-2.

A modern digital equivalent would be the Active Format Description, a standard set of codes that can be sent in a MPEG video stream, with a similar set of aspect ratio possibilities.

625 line systems

For 625 line analog TV systems (like PAL or SECAM), the signal is placed in line 23. It begins with a run-in code and starts code followed by 14 bits of information, divided into four groups, as shown on the tables below (based on Rec. ITU-R BT.1119-2) :

Group 1 - Aspect ratio
Bits (0 to 3) Aspect ratio Picture placement inside the broadcast area Active lines
0000 - - -
0001 Full format 4:3 576
0010 Letterbox 16:9 top 430
0011 - - -
0100 Letterbox 14:9 top 504
0101 - - -
0110 - - -
0111 Full format 14:9 centre shoot and protect 14:9 (see note) 576
1000 Letterbox 14:9 centre 504
1001 - - -
1010 - - -
1011 Letterbox deeper than 16:9 centre undefined
1100 - - -
1101 Letterbox 16:9 centre 430
1110 Full format 16:9 anamorphic 576
1111 - - -

Note: The transmitted aspect ratio is 4:3. Within this area a 14:9 window is protected, containing all the relevant picture content to allow a wide-screen display on a 16:9 television set.

Group 2 to 4
Bit Item Group
4 Camera Mode (interlaced) / PALplus Film Mode (progressive scan) 2 - Enhanced Services
5 Conventional PAL / PALplus Motion Adaptative Colour Plus encoding
6 No Vertical helper / PALplus Vertical helper present
7 Reserved / Ghost cancellation
8 No subtitles / subtitles within teletext 3 - Subtitles
9 No open subtitles / Subtitles in active image area
10 Subtitles out of active image area / Reserved
11 No surround sound / Surround sound mode 4 - Reserved
12 No copyright asserted or status unknown / Copyright asserted
13 Copying not restricted / Copying restricted

525 line systems

525 line analog systems (like NTSC or PAL-M) made a provision for the use of pulses for signaling widescreen and other parameters, introduced with the development of Clear-Vision (EDTV-II), a NTSC-compatible Japanese system allowing widescreen broadcasts. On these systems the signals are present in lines 22 and 285, as 27 data bits, as defined by IEC 61880.

The following table shows the information present on the signal, based on Rec. ITU-R BT.1119-2 ("helper" signals are EDTV-II specific):

Bit Item
1 Reference signal
2 Reference signal
3 Aspect ratio (4:3 full format / 16:9 letterbox)
4 Even parity for B3 to B5
5 Reserved
6 Field type (First field / Next field)
7 Frame type (Reference frame / Other frame)
8 Vertical temporal helper (no / yes)
9 Vertical high resolution helper (no / yes)
10 Horizontal helper (no / yes)
11 Horizontal helper pre-combing (no / yes)
12 to 14 For TV station use
15 to 17 Reserved
18 to 23 Error correction codes for B3 to B17
24 Reference signal
25 to 27 Confirmation signal

See also


This page was last updated at 2024-03-24 22:48 UTC. Update now. View original page.

All our content comes from Wikipedia and under the Creative Commons Attribution-ShareAlike License.


Top

If mathematical, chemical, physical and other formulas are not displayed correctly on this page, please useFirefox or Safari